MMillennium CPS
English
←All sections

Diagrams and factory photo tour

Electrical panels are drawn and linked into a diagram, and every device has its own card with a photograph and its label. The photo tour lets you walk through the factory in a browser and open a panel straight from the panorama.

  1. 1A panel is photographed, the system reads its contents from the images and proposes a draft diagram.
  2. 2A person confirms it, and the diagram then checks itself: overloaded branch, supply loop, mismatched voltages.
  3. 3The diagram can be printed, exported to a drawing, and it keeps every version.
Diagram check
LevelSheetFinding
CriticalWorkshop 1 panelSupply loop: KM1 → KM2 → KM1
WarningWorkshop 1 panelBranch Q3 loaded to 27 A against a rating of 25 A
InformationWarehouse panelSupply not traced for 4 devices

What this gives you

Switchboards read from photographs

Photograph the cabinet and the system identifies the devices, their ratings and the wiring, then proposes a draft schematic. An engineer confirms it, so nothing invented reaches the drawing.

Schematics check themselves

Supply loops, branches overloaded in amps or kilowatts, mismatched voltages and devices with no supply are all raised automatically.

A record for every device

Photograph, label, rating and position in the row. The image of each device is cropped from the overall shot automatically.

QR label on the panel

A sticker on the cabinet door opens that panel's schematic on the electrician's phone.

Photo tour of the plant

Walk through the workshop in a browser and open the panel you need straight from the panorama.

Printing and CAD export

Large schematics are tiled across sheets with an overlap instead of being shrunk into something unreadable, and there is an export to CAD format.

Inside this section

The data shown in the screens below is fictional.

Diagrams

The factory's diagrams — electrical, network and CCTV: a card and photos for every device. The page has three tabs: "Diagram" (where you draw the switchboard), "Device register" (the list of all devices) and "Analysis" (logical errors in the diagram).

  • ✓Create a new sheet — the "New sheet" button (one sheet = one switchboard, floor or workshop); the position of the switchboard and any notes about the door go in the sheet's "Description" field
  • ✓Add a device — the "Add device" button opens the palette, then drag the button onto the diagram or click it; the card opens straight away and a photo can be uploaded right there
  • ✓Draw a connection — "Draw connection" or the blue dot under the selected block; the arrow points at the consumer, that is, it shows "who feeds whom"
  • ✓Upload photos of the switchboard to the sheet — "Add picture" or "Folder" (to select a whole inspection folder) in the "Sheet photo survey" strip
  • ✓Have a diagram built from the pictures — "Build diagram from pictures"; the reading runs on the server, you may close the page, and at the end a draft list opens which you confirm with "Add to diagram"
  • ✓Put it on paper — "Print / PDF" (the "With analysis notes" box, "Landscape" / "Portrait"; a large sheet is split into pages automatically) and QR labels with the "Label" button ("A4 — 8 labels per sheet", "A4 — 1 large label", "Thermal printer 80×40 mm") — scanning a label with a phone opens that sheet or device card

Photo tour

A panoramic tour of the factory: you move from point to point and drag the panorama to look around. The markers in the panorama either take you to another point (➜) or open the diagram sheet for that switchboard (⚡).

  • ✓Look at the panorama — drag: look around, wheel: zoom
  • ✓Click a ⚡ marker to open the diagram sheet for that switchboard (it goes straight to the "Diagrams" section)
  • ✓Move to a neighbouring point with a ➜ marker, or click a point on the "Factory grounds" mini-map in the corner
  • ✓Create a new point — "New point": select the camera's ready-stitched files (DJI_…_A01.JPG, 3 files per point, taken clockwise), enter a name and press "Upload and create"
  • ✓Have a panorama assembled from separate shots — "Stitch panorama (from shots)", "Upload and queue"; progress appears live on this same page in the "Panorama processing" section
  • ✓Place a marker — "Add marker", click a spot in the panorama, enter the "Caption" and choose the "Target type": "Diagram sheet (⚡)" or "Another tour point (➜)"